Barebone Waveshare

Adatto per valutare il Raspberry Pi CM4 o essere integrato nei prodotti finali. Potenti funzioni in un corpo delle dimensioni di una carta di Presa standard CM4 e intestazione Raspberry Pi 40… (continua)

Support Raspberry Pi Pico expansion board ecosystem to satisfy creative IoT application development. Xtensa single-core 32-bit LX7 microprocessor, ESP32-S2FH4, support clock frequency up to 24… (continua)

Onboard voltage translator, compatible with 3.3V/5V operating voltage I2C communication interface, control the module on/off via IO pins Ranging distance: 40 4000mm,ranging accuracy: ±5%, rang… (continua)

The CC Debugger is primarily used for debugging and programming the flash on CCxxxx 8051-based System-on-Chip SoC devices from Texas Instruments CC Debugger also supports CCxxxx RF transceiver… (continua)

This is a 24-bit high precision barometric pressure sensor, which allows accurate altitude tracing, as well as barometric pressure / temperature measuring Supports I2C default / SPI interface,… (continua)

Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano I2C interface, only 2 pins are required for moving and light intensity sensing; Onboard PCA9… (continua)

A general RGB OLED display Module, 1.5inch diagonal,128x: 128 high resolution, 65K colors, clearly displays colorful images Supports 4-wire SPI OR 3-wire SPI interface, configured via onboard … (continua)

Provides HTML host code, allows to refresh display content via remote webpage, suit for Internet applications Onboard ESP32, supports Arduino development; Provides Arduino APP, allows to refre… (continua)

M0 series 32-bit ARM processor, fast speed, high efficiency;10/100M Auto-MDI/MDIX ethernet interface, regardless of cross-over or straight-through cable Configurable RS485 baudrate 600bps: 230… (continua)

Note: The new Jetson Nano 2GB Developer Kit is NOT supportedï �'�This is a dual mode wireless NIC module applicable for Jetson Nano, supports 2.4GHz / 5GHz dual band Wi Fi and Bluetooth 4.2. … (continua)

This is a general OLED display Module, 1.5inch diagonal, 128x: 128 pixels, 16 gray scale, with embedded controller, communicating via SPI or I2C interface. 128x: 128 high resolution 16 gray s… (continua)

This is a general OLED display Module, 1.5inch diagonal, 128x: 128 pixels, 16-bit grey level, with embedded controller, communicating via SPI or I2C interface. 128x: 128 high resolution,6-bit… (continua)

The Motor Driver HAT is designed for Raspberry Pi, controlled via I2C interface, will drive two DC motors at the same time. É una scelta ideale per te per robot mobili. Raspberry Pi connetti… (continua)

This driver board gives your micro:bit the ability to drive two channel DC motors and three channel servos. It's an ideal choice for you to DIY mobile robots micro:bit edge connector, direct… (continua)

Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards I2C controlled, by setting 5 address jumpers, it is stackable up to 32 this modules; Reserved I2C control… (continua)

Onboard ESP32, supports Arduino development;Easy to be integrated into wireless applications. Provides Android APP, allows to refresh display content via Bluetooth EDR. Provides HTML host co… (continua)

Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards. Adopts SC16IS752+SP3485 dual chip combination, converts SPI to RS485, data rate up to 921600bps. Allow… (continua)

This is a general RGB OLED display Module, 1.5inch diagonal, 128x: 128 pixels, 16-bit high color 65K colors, with embedded controller, communicating via SPI interface 128x: 128 high resolutio… (continua)

This is a general RGB OLED display Module, 1.5inch diagonal, 128x: 128 pixels, 16-bit high color 65K colors, with embedded controller, communicating via SPI interface. 128x: 128 high resolut… (continua)

This is a flexible E-Ink display HAT for Raspberry Pi, 2.13inch, 212x: 104 resolution, with embedded controller, communicating via SPI interface, supports partial refresh No backlight, keeps d… (continua)

Raspberry Pi Connectivity, compatibile con Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+ I2C controlled,using only 2 pin,up to 16-Channel servvo/PWM outputs,12-bit resolution for each channel 409… (continua)